Specific heats and enthalpies of technical solids at low temperatures
Read Online

Specific heats and enthalpies of technical solids at low temperatures a compilation from the literature by National Bureau of Standards.

  • 257 Want to read
  • ·
  • 16 Currently reading

Published by N.B.S. in Washington .
Written in English

Book details:

Edition Notes

Statementby R.J. Corruccini and J.J. Gniewek.
SeriesNBS Monograph -- 21
ContributionsCorruccini, Robert J., Gniewek, J J.
ID Numbers
Open LibraryOL20111182M

Download Specific heats and enthalpies of technical solids at low temperatures


Corruccini, R.J., and Gniewek, J.J. SPECIFIC HEATS AND ENTHALPIES OF TECHNICAL SOLIDS AT LOW TEMPERATURES. A Compilation from the Literature. United States: N. p., Get this from a library! Specific heats and enthalpies of technical solids at low temperatures; a compilation from the literature. [Robert J Corruccini; John J Gniewek]. Neodymium and Er 3 Ni powders were produced and examined as possible candidates for use as regenerator matrices in the regenerative heat exchanger of the Gifford-McMahon cycle refrigerator. In the case of Er 3 Ni, crushed powders were brittle and angular in shape, molten salt produced spheres were heavily oxidized, and gas atomized powder had a low yield (3%) and a large fraction of hollow Cited by: 6. The quasi-low temperature behaviour of specific heat is verified here with experimental data for the fcc lattice materials, silver chloride and lithium iodide. The conjecture that the fourth order behaviour is universal for all condensed matter systems has also supported the data for glassy matter: vitreous by: 3.

mon solids, aluminium and carbon, which have low specific heats at these temperatures, prompted us to design an experiment for undergraduates. Description Nernst (, ) used a vacuum insulated calori- meter to determine specific heats at low temperatures File Size: KB. Heat capacities of solids. Heat capacities of solids. Any theory used to calculate lattice vibration heat capacities of crystalline solids must explain two things: 1. Near room temperature, the heat capacity of most solids is around 3k per atom (the molar heat capacity for a solid consisting of n-atom molecules is ~3nR).File Size: 87KB. For solids at low temperatures, the difference comparison, the specific heats of two gases commonly used in cryogenics are plotted with dashed lines. Heat capacity of metals At low temperature, it can be that the of enthalpiessolid materials, such asseen G10 (which is aCited by: The essential input to the fitting procedure is a table of specific heat, enthalpy, and entropy as a function of temperature. In addition since the fits span two temperature ranges, the temperature ranges have to be specified. Generally speaking, the common temperature connecting the two ranges is K, but it may be different in some cases.

  The specific heat and thermal conductivity of mm- and mmdiameter spheres of Pb are reported (2–30 K). The former spheres are % Pb, the latter spheres are Pb + 5% Sb. Both types of spheres undergo a superconducting transition at 7 K, and the changes in the specific heats at the transition correlate well with the electronic coefficient determined for bulk by: 2. TECHNICAL RC DATA SHEET Features and uses of RC RC is a ternary mixture non-azeotropic composed of R, R and Ra. It is chemically stable, has good thermodynamic properties, low environmental impact and very low toxicity. Although one of its components, R, is flammable, the overall mixture composition is formulated so that. TableLinearthermalcontractionandcoefficientsoflinearthermalexpansion Elements Aluminuin Antimonyt Berylliumt Bismuth Cadmiumb T 10«dLjg.,£iT dijg,£ File Size: 2MB. Appendix: Estimation and Correlation of Specific Heat 72 Specific Heat at Low Temperatures 76 Specific Heat at Moderate Temperatures 77 Specific Heat at High Temperatures 80 References 82 Chapter 2. Calorimetry Below 1 К 91 Introduction 91 Problems Encountered in the Temperature Range К 92